How Can I Set The Motion Detector Off On My 808 Camera

The 808 is a small colour video camera with audio that also takes photos. The 808 keychain micro-camera provides a fully functional digital camera and video recorder small enough to hide in the palm of your mitt.

Specifications

Brand new model of 808 Automobile Central Concatenation Micro Camera, identified by Chuck Lohr'southward web site every bit #16, and now it'due south available!
1/four" CMOS WXGA Hard disk Sensor / H.264/AVC1 DSP / Hynix 512M DDR2
Rechargeable LIPO Battery (250mah), with Battery Charger Manage IC
Video: 720P HD H.264/AVC1 video codec, 1280 ten 720 30fps .mov
Photo: JPG 1280*960 (no degrading by upsizing to interpolated "five megapixel" size)
microSD card slot, supports up to 32GB (memory card not included), suggest using Class 4 or above
USB2.0, plug and play, easy connection with computers, no driver needed.
Super mini size, just around 50mm (50) x 32mm (W) x13mm (H)
Super light-weighted: only approx 17g!
Multifunctioned, you tin use information technology equally a mini DVR, a camera, a webcam, a removable USB drive

What's special nigh this 808 #sixteen camera?

1. A connector added for the internal bombardment, making it changeable by users who don't like soldering. You don't take to throw your camera away when the battery dies. You just need a new bombardment and alter it!

ii. A connector added to the lens/sensor module, make it possible to replace or upgrade information technology when new module's available.

iii. New Lens and totally new circuit board design. You will encounter below improvements in video:

Overall sharpness: improved
White residuum control / colour shifting issue: improved
Saturation / and contrast boost effect: colors await much more natural now
Darker corner/border vignetting issue: improved

4. Low battery buzzing artifact in video -Gone!
v. Y'all but need one Standard USB Information cable for charging and information commutation with your computer. You don't need another special charging cablevision to tape videos while charging. Just i cable is OK.
six. Information technology supports sound volume control, and you tin even get it mute to save battery and helps to increase the recording time when the audio is non needed, it can be fix by TXT config tool.
7. It supports optional Loop Recording, it can be set past TXT config tool.
8. You can ready the appointment and fourth dimension (white much smaller on the lower left corner), and toggle the engagement/fourth dimension stamp on or off, by TXT config tool.
ix. Sometimes you lot may don't want 720P recording to salvage battery and retentivity card chapters, at present you can toggle video output frame size from 1280×720 30fps (default), to 848×480 30fps, or 640×480 30fps.
10. Optional AVI output: we also accept some other firmware choice available which will output .AVI file format, using the same H.264 codec, and information technology offers seamless recording (at that place is no lost video betwixt clips). If you lot need it, delight send a message to us, and we will send information technology to you by email.
11. And more. Please notice more details in the PDF manual. And of course on RC Forum Tom Frank'south keen thread, yous will find lots of helpful information there.

#16v2 pros and cons compared to the #16v1.

PRO – Wider angle of view, about 78 degrees. Composite video output. Price is however about US$twoscore. Exposure to a blue sky does non cause a temporary gray and yellow colour shift similar the #16v1.
CON – More vignetting. Exposure tends to be a center bright area (hot spot) and night edges. The video-out shortens the recording fourth dimension by about ten minutes.

The (#16v2) TV video-out role does not impact the recorded video quality… it just shortens the recording time by about ten minutes.

111204C16BatterySide

111204C6ButtonSide

Pedagogy Manual for the #16 Camera

The Shutter button is the minor button all the fashion to the front end.

The Power button is the larger push, right behind the shutter push button.

The Reset push button is located nether the small pinhole situated between the USB connection and the SD menu slot. It tin be pressed using the end of a paper prune or similar object. Briefly pressing the reset button will force the photographic camera to stop any it is doing and turn off.

The other two buttons are dummy. They have no function.

A new, fully charged battery will last about 45 minutes in the keychain model.

You may employ any micro SD or micro SDHC card with a capacity of upward to 32GB with this camera. To avoid menu compatibility issues, e'er use quality cards with a speed rating of Class 4. Some cards with a faster speed rating may not work properly. The camera only supports cards formatted with FAT32. Cards larger than 32GB, for case micro SDXC volition not work with this camera. See below "Breaking the Rules" of how to overcome this limitation.

Cables

The camera requires a standard USB cable for charging, connecting to external bombardment packs
for continuous recording and for connecting to the PC as an external disk or webcam.
All models manufactured in July 2012 and subsequently comprise a Video-Out function with the
bespeak output connected to pivot #4 on the mini-USB socket. Special cables can be ordered
from the supplier or yous can make one yourself.

You must under no circumstances use any other "special" cable, especially the "special"
cable supplied with the #eleven (the predecessor to the #16). Doing so will destroy your
camera. And then, do non use a #11 "special" cable under any circumstances.

Versions

On the original Hardware there was no video-out (composite video).
July 2012 saw the release of V2, a new Hardware design which includes a video-out (Tv set
composite video) betoken. This signal is connected to USB pin #4, the final available pin on the
mini USB socket. Unfortunately, an active video-out bespeak consumes up to 25% of bachelor
bombardment power. In order to turn off the video bespeak using parameter settings, firmware versions
greater than v0.29 are required. For the longest recording times possible, but only if video-out
is not required, the video-out parameter should always be ready to "Off".

Before yous start

Before using the camera for the get-go time, ensure that it is fully charged. Encounter beneath under "Charging".

LED status indicators

Since the camera has many functions, information technology'due south important to understand the pregnant of the LEDs.

The following LED states are for a camera not continued to the PC.

Yellowish LED remains on:
• Photographic camera is in Video recording standby mode.

Yellow LED slowly flashes fifteen times and and so the camera turns off:
• The memory card is total or not inserted.

Yellow LED constantly slowly flashes (one sec. On, 1 sec. Off):
• The photographic camera is recording video. The Video Recording indicator (come across configuration) must be ON for this to work.

Yellow LED flashing very fast:
• Firmware update in progress. DO Non press any buttons until all LEDS are off.

Yellow LED flashes quickly 5 times and then the camera turns off:
• This indicates a serious error condition. See Trouble Shooting.

Crimson LED remains on:
• Camera is in Photo recording standby mode.

Ruby-red LED flashes twenty times and then the photographic camera turns off:
• Depression battery.

Cerise LED flashes three times and then the camera turns off:
• The photographic camera is turning off, either automatically or manually.
• Notation: The camera will only flash while turning off if the Recording Indicator has been configured to be on while recording. The LED will not flash if the Recording Indicator has been configured to be off while recording (clandestine mode).

Green LED is on:
• The battery is charging. Connecting the camera to the PC

Always connect the camera direct to the PC. Exercise not use a USB hub.

Charging

Connect one end of the supplied standard USB cable to the camera.
Connect the other end to a USB, 5V DC ability source (wall charger, PC or external battery).
When charging, the green LED will be on.

When charging is finished, the green LED volition be off.

Charging takes about two.5 hours for a fully discharged battery with the camera turned off and
connected to an external USB Charger. With some batteries the greenish LED may not plow off
immediately or may even take up to four.5 hours or longer to turn off. However, it is safe to
presume that after 2.5 hours the battery is fully charged, fifty-fifty if the green LED remains on.
Batteries are non covered under warranty. Charging is limited to around 140mA which offers
the best possible long-term bombardment protection. If charged with under-rated chargers or using a
USB hub without an boosted power supply, expect longer charging times. For optimum
results, the charging voltage should be +5V under load.

Formatting

Standard formatting tools provided by the operating system are not always reliable. Also, they
practise not optimize the SD card's functioning. For optimal carte du jour performance it is recommended
to always use the camera'south built-in formatter. Instructions for In-Photographic camera Formatting are
outlined below under "In-Camera Formatting". Some other excellent formatting utility is "SD
Formatter" which can be downloaded from www.sdcard.org/downloads/formatter_3/. This
utility has been specifically designed for formatting SD cards.

Automatic Ability Off from Standby mode

If the camera is in Standby manner (Video style or Photo Mode) you must have a moving picture(s) or
start a video recording within *thirty seconds. The camera will automatically turn off after *thirty
seconds of no activity.

*This value tin can be set up using the setup program. Automatic Power Off can also disabled.
If the camera is used for monitoring just, for example fpv, it is imperative to ensure that
Automatic Power Off is disabled in society to prevent bespeak loss when Standby times out. Turn on Camera
Firmware v0.49 and earlier: Press and concur the Power Button for max. two secs. until the Red
LED turns on.

Firmware v0.52 and later: Power-On can be configured equally "fast" or "delayed". In fast fashion,
the camera will turn on immediately the Power Button is pressed. In delayed mode, press and
hold the Power Button until the Xanthous LED turns on. See additional information below nether "Special functions".

• If the camera has been configured with "Auto Tape" set to On, the camera will
automatically begin recording after 4-5 seconds. The yellow LED will blink iii times
indicating that recording has started. If the photographic camera has been configured to show the
recording indicator while recording, the yellowish LED will slowly flash at 2 second
intervals, otherwise the yellow LED will be off.

• If the photographic camera has been configured with "Auto Tape" set to Off (default setting), the
camera will switch to video standby mode after about 1 second and the Yellow LED will
turn on.

• If the camera has been configured with "Motion Notice" set to ON, the camera will start
to record as presently as motion is detected. The yellow LED will glimmer 3 times indicating
that recording has started. If the camera has been configured to bear witness the recording
indicator while recording, the yellow LED volition slowly wink at ii second intervals,
otherwise the yellow LED will exist off. If no motility is detected inside a given period of
fourth dimension the camera volition return to standby mode and volition merely start recording once again when
farther motion is detected. With Firmware v0.52 and above, motion sensitivity
and timeout delay can be configured.

• "Automobile Record" and "Motion Detect" are conflicting values. It is not possible to set both
to "on".

Turn off Camera

Press and hold the Power Button for about 3-5 secs. The scarlet LED may also blink 3 times –
run into "LED status indicators". Note: If the camera is recording, the recording should first be
stopped (see below).
Switching between Video and Photo Standby modes
The photographic camera tin can be switched betwixt Video Standby and Photograph Standby by briefly pressing
the power button. When the camera is in Video Standby, the Xanthous LED will be on. When the
camera is in Camera Standby, the Red LED will be on. Recording Video (from Video standby mode, Yellow LED is on)

Start video recording.

• Briefly press the shutter push. The xanthous LED volition flash 3 times to indicate that
recording has started. If the camera has been configured to show the recording
indicator while recording, the yellowish LED will slowly wink at 2 second intervals,
otherwise the xanthous LED volition be off.

Finish video recording.

• Briefly press the shutter push button. The yellow LED flashes twice.
Have a Photo (snapshot) while recording:
• Briefly press the ability button to take a picture. The yellow LED will wink twice.
• If Time-Lapse photo has been configured (Firmware v0.47 and above), the camera will
keep to take pictures until the shutter button is pressed. The yellowish LED volition flash
each time a motion picture is taken. More information is availyble beneath under "Special
functions".

Taking a Photo (from Photo standby mode, Blood-red LED is on)

• Briefly press the shutter button. The yellowish LED flashes twice and and so turns back on.
Webcam Manner
• Remove the flash memory bill of fare.
• Connect the camera to the PC using a standard USB cable.
• Press the Power Button for max. 2 seconds until the Red LED turns on. The xanthous
LED will plough on while initializing the connection to the PC. It will turn off when
continued and the red LED will turn back on indicating a successful connection.
• ► If this is the starting time fourth dimension you lot have connected the photographic camera in WebCam mode, Windows
volition automatically install the required drivers.
• The camera is now in Webcam mode.
• First your favorite WebCam software, such as AMCap. If your screen is black, the
software is not configured correctly. Make sure the program shows the "USB PC
photographic camera" every bit the "device" selected for video capture. If this option does not show in the
"device" pick list, restart the webcam program and check again.

Removable Disk Way

• Make sure a memory card is inserted.
• Connect the camera to the PC using a standard USB cable. The green LED may turn
on indicating that the bombardment is charging.
• Press the Power Button for max. 2 seconds until the red LED turns on. The Yellow
LED volition turn on while the connectedness is beingness initialized and turn of when the camera is
continued. The red LED may remain on or be turned off. The Green LED may besides be
on, indicating that the bombardment is charging.
• The camera is now in Disk Mode and a new removable drive should be bachelor on
your computer. This may take up to thirty seconds.
• ► Note 1: The Red LED will flash during all read/write data transfers with the camera.
• ► Note 2: You may also turn on the camera before connecting to the PC. In-Camera Formatting
The Camera contains a built-in formatter which may exist used to format the SD bill of fare. Do non
format SDXC cards (cards with a capacity of 64GB and more) encounter below "Breaking the
Rules". In-Photographic camera formatting is best done using Nr16Setup.exe (run into beneath) only tin can as well be
done every bit follows:
• Connect the Camera equally a Removable disk (see higher up).
• Press and hold downwardly the Shutter button. DO NOT RELEASE the button.
• Disconnect the camera from the figurer.
• Later about 4-half-dozen seconds the camera will turn off (the red LED may as well blink 3 times –
see "LED status indicators"), indicating that formatting is completed.
• Release the shutter button.
Camera Setup (Configuration)
On Windows information technology is recommended to always use the Windows Program Nr16Setup.exe to
alter the camera's configuration. Nr16Setup.exe will also run on Mac and Linux versions if
Wine is installed. However, it is also possible to manually edit the "SYSCFG.TXT" file which
must be placed in the root folder of the card. You tin can utilise whatever ASCII editor, for instance
Notepad, to modify the parameters. The "SYSCFG.TXT" must be in plain ASCII, it must not
be in Unicode. If you lot don't know what a root folder is, or you don't know what ASCII is or don't
know how to manually edit ASCII files please only use Nr16Setup.exe.
A "SYSCFG.TXT" file can exist automatically generated by the Camera and will exist placed in the
card's root directory. The photographic camera's parameters are self explanatory. Information technology is important not to
change the sequence of the foursquare brackets and not configure invalid combinations. For
example, never combine a clip longer than v minutes with the continuous loop. If you lot enter
invalid combinations or values, the Camera will non perform as expected. It is much safer to
employ the setup plan which will always configure the photographic camera correctly.
The "SYSCFG.TXT" file tin can be automatically generated every bit follows:
1. Disconnect the photographic camera from the PC and plow it off.
two. Printing and Hold Downwardly the Shutter push button. DO Non RELEASE the push button until
step vi.
three. Printing the Power button until the photographic camera Yellow LED turns on. This volition take well-nigh
1 second.
4. Release the Power button.
five. Await until the Yellow LED turns off. This will accept well-nigh 8-9 seconds.
6. Release the Shutter button.
The camera is updated with the parameters defined in the "SYSCFG.TXT" file by using
exactly the aforementioned method as outlined in a higher place. Once completed, the "SYSCFG.TXT" file will be
deleted from the carte's root folder.
Using Software to configure the camera
Nr16Setup.exe will automatically configure the photographic camera with the parameters you crave.
Detailed instructions tin can be found in the plan past clicking the "Help" button.
All firmware versions from v0.47 enable Nr16Setup.exe to straight communicate with the
camera using the USB connection. Setting parameters using the "SYSCFG.TXT" file is no
longer necessary. Bootloader Update
The bootloader is responsible for correctly loading and updating the firmware. Bootloader V3
and in a higher place makes it a petty easier to update the firmware, but in that location are no other advantages.
Installing the bootloader requires the exact same procedure every bit installing the firmware, which
is described below. The bootloader is installed inside a 2d or ii as opposed to upward to 12
seconds required to install the firmware.
Firmware Update
Usually, in that location is no need to update the firmware. You should only update the firmware if you
are having problems with the current firmware or the new firmware provides functionality you
crave that are not available in your current version.
The latest firmware version tin can be downloaded and installed directly from the setup program
or installed manually by downloading the firmware file from
http://www.rcgroups.com/forums/showpost.php?p=20149719&postcount=four.
Updating the firmware is an easy and safe process.
If your photographic camera was purchased earlier November 2012 and has not been updated with
bootloader V3 or greater you will ordinarily need an external card reader (not another #16!) in
order to update the firmware, but in that location is a "Backstairs" method which is outlined below. Since
all the parameters can be fix programmatically using parameters, it is not necessary to load
different firmware versions for different configurations. The only exception is for the video
output format. Because of lack of retentiveness space, dissimilar firmware versions exist for AVI and
MOV formats. The AVI format produces non-standard .avi files with a 1 second overlapping
video sequence between clips. The MOV format produces videos which have a 2-3 2nd
gap between clips.
Transmission Firmware Update
Note: Unless the photographic camera is running bootloader V3 or in a higher place, the firmware file will Not exist
automatically deleted from the flash card when the photographic camera is turned on. The camera will exist
UNUSABLE and reload the firmware file every time it is turned on until a card is used that
has no firmware file on it. This is the reason that y'all MUST delete the firmware file, after
the update has completed, using an external carte reader or the "backstairs" method
described beneath.
• Copy the new firmware file into the camera's flash card root folder. This tin be done
with the menu in the camera continued to the computer as a Removable Bulldoze, or
externally in a card reader. Notation: All firmware files are named FWMICDVR.BIN. The
name must not be changed.
• Disconnect the photographic camera from the computer and make certain information technology is turned off.
• Insert the wink menu containing the new firmware file into the camera (if not already in
the camera).
• Press the Power button very briefly until the Yellow LED turns on and begins to flash.
Do not go along it pressed any longer.
• Release the Power Push button. The Xanthous LED will go on to wink very quickly for a
2nd or two and and then will remain on for up to 12 seconds. It may besides glimmer a few
times. This indicates that the firmware is being written into the camera. DO NOT
PRESS ANY BUTTONS while the yellow led is on or flashing!
• When the firmware is fully installed, the Yellowish LED will turn off and the camera will
shut down.
• If the camera is running bootloader V3 or above the camera will automatically restart
and the yellowish LED will remain on. The firmware update is consummate.
For cameras running an earlier bootloader, go along as follows: • *Remove the card from the camera and insert it into a card reader. You cannot use
another #sixteen camera for this, simply you can use the "Backdoor" method described below.
• Delete the firmware file.
• Remove the card from the carte reader and insert information technology into the camera.
• The photographic camera is at present set up for use and has the update firmware loaded.
*Backdoor Method to delete firmware file
If an external card reader is not available, you tin can delete the firmware file from the menu as
follows:
• Make sure the camera is turned off.
• Remove the card from the photographic camera.
• Plow on the camera.
• Insert the menu back into the camera.
• Connect the camera to the PC using a standard USB cable.
• The camera will now be available as a removable deejay.
• Delete the FWMICDVR.BIN from the disk.
• Unplug the camera from the USB.
• The camera is at present ready for utilise and has the update firmware loaded.
Recording using an external power supply
With this camera, it is possible to charge the battery and tape at the same time using a
standard external USB 5V DC power supply. The power supply may be mains driven (normal
household wall plug), or run off batteries, including the car charger USB plug (optional
accessory) and cable supplied with the photographic camera.
External USB power supplies normally only utilise the +5V and the – (Ground/Globe) wires. The two
data wires are normally not used. All the same, some USB ability supplies designed for a specific
USB device may employ dissimilar wiring schemes and thus may not work with this camera. To
avoid possible bug, always employ a generic power supply.
When turned on, the camera checks for an electric signal on the ii Information wires. If a signal is
establish, the camera assumes it is connected to a PC and recording volition non be possible – see
below "Recording when directly connected to a PC".
For recording video or taking pictures using a standard external power supply connection, the
USB power supply can exist connected at any fourth dimension, i.e. earlier the photographic camera is turned on, before
the recording is started, or after the recording has been started.
► If external power is connected and the camera is and then turned on, the camera will cheque the
data lines to determine if it is connected to an external ability supply or to a computer.
Considering of this, it will accept up to 5 seconds until the photographic camera is "set", even though the
yellow LED turns on much earlier.
Recording when directly connected to a PC
With this camera, it is possible to charge the battery and record at the aforementioned time while
connected to a PC.
In order to tape video while the photographic camera is connected to a PC, the video recording must be
started before the camera is continued to the PC. It is not possible to record if the camera is
turned on while connected to a PC. Likewise it is not possible to take pictures while the
photographic camera is connected to the PC. Breaking the Rules
As stated in the introductory, this camera but supports micro SD and micro SDHC Memory
cards. These cards are formatted in FAT32, which is the format the camera requires.
Microsoft has imposed an bogus limit on the maximum chapters of the FAT32 file organization of
32GB fifty-fifty though, theoretically, a limit of ii Terabytes is possible.
Large chapters micro SDXC (Xc=Extended Chapters) cards first with a capacity of 64GB. It is
not possible to read these cards with normal SD or SDHC card readers, which includes this
photographic camera. SDXC cards can only exist read with special SDXC card readers. SDXC cards placed
in a normal SD(HC) reader may be recognized by the operating organization, but volition be found to
exist unformatted, which is not right. If formatted using Windows, they will probably be
formatted with 16GB total capacity!
SDXC cards will be recognized correctly if used in an SDXC bill of fare reader and the file system
will be exFAT. The maximum capacity of exFAT is ii Terabytes.
If y'all use the "In-Photographic camera Formatting" to format your SDXC cards, you lot practise and then entirely at
your own risk. The Manufacturer takes no responsibility for incorrectly formatted cards and
the consequences that may arise (for example destroyed cards). SDXC cards formatted with
FAT32 are not supported by Microsoft and you will possibly invalidate your bill of fare's guarantee
by doing so.
Using In-Camera Formatting it is possible to format SDXC cards in FAT32 Format. Doing and then
will plow the cards into out-of-specification SDHC cards. Still, you will have the
advantage of much college menu capacities. For example, a 64GB SDXC card formatted with
FAT32 will give you well-nigh 20 hours of continuous video when recorded with a data rate of vii
Mb/southward. After formatting with FAT32 these cards will be recognized past Windows using normal
SD(HC) card readers, which includes this camera, to their total capacity. Note that the max. file
size of 4GB still applies.
SDXC cards formatted with FAT32 may exist converted dorsum to exFAT by using SDFormatter
but an SDXC card reader must be used.
Special functions
The following functions need boosted explanation:
Power-on Delay
This parameter was added in v0.fifty and gives the user the selection of the existing 2-3 sec.
delayed power-up, or an instantaneous power-up with no delay. Note that the arrangement requires
virtually ii seconds afterward power-on until the buttons become active.
Audio Volume
Equally of v0.67, when the volume is turned OFF, the sound track is completely eliminated from
the video output stream in all camera modes. Prior to this version a audio runway was attached
to the video simply with the volume turned off. The new functionality will costless up a nominal
7% video recording space when the volume is turned off. Motion detection
Movement detection was introduced in v0.49 and additional parameters for adjusting the
sensitivity and timeout were introduced in v0.58. If motion detection is enabled, Auto Record,
Auto-shutoff, Fourth dimension-lapse Photos and Boob tube Video-Out must be disabled. Motion detection starts
automatically later on a five sec. delay later the camera is powered on. During the filibuster period, the
photographic camera can be:
• Toggled into normal video mode by pressing the shutter button. The camera will revert
dorsum to normal Motility Detect manner when normal video is stopped with Shutter Button.
• Toggled to Photo Mode with the power button.
• Placed into position to prevent the motion from turning on the camera and starting the
first motion-triggered prune.
Recording will continue as long every bit in that location is movement detected. If no more movement is
detected, the camera volition enter a timeout loop and cheque for more motion. If no new motion is
detected during the timeout loop the photographic camera volition stop recording and await for further movement
when it will kickoff recording once again. This procedure will be repeated ad infinitum.
Once motion is detected, it will take a second or 2 until the firmware starts recording. This
filibuster tin can't be avoided because of technical limitations.
.
Time Lapse
Time Lapse was introduced in v0.43 and further refined in v0.l. If Fourth dimension Lapse is enabled,
Auto Record and Move detect must be disabled. Photo delay settings also include 0.fifty and
0.25 secs. If these two low settings are used, Photo Frame size must be set to 1280×720 and
the Time stamp must exist disabled. The Automobile-shutdown setting tin remain agile with Time
lapse turned on because it will only function when the camera is toggled out of photograph fashion
back into standby fashion. The 0.25 sec. filibuster between images, when joined into a movie at
30 fps, will equate to a 7.5x time lapse speed upwardly.
Video Frame Charge per unit
This parameter was added in v0.50 and allows recording video with frames rates of 5, x, fifteen,
20, 25, or 30 fps. These can give additional time lapse video modes::
• The v fps mode is special, and volition automatically play back at xxx fps. This means the
NATIVE video in this style will give a 6X speed-upward with NO editing!
• The other frame rates play back at the same frame charge per unit as the capture charge per unit (e.g., 10
fps capture volition play back at 10 fps – no speed up, but hasty move).
Editing the special frame rates to play dorsum faster can produce slower "time lapse" movement
than the Time-lapse Photo settings, e.thou.:
• 5 fps video at 30 fps = 6x speed up
• 10 fps video at 30 fps = 3x speed upward
• 15 fps video at xxx fps = 2x speed up
• twenty fps video at 30 fps = i.5x speed upwardly
• The 25 fps manner is currently not available due to incompatibility with new library code
from the chip vendor. When a fix id released it volition exist added. If this value is ready, 30fps
will be used instead. Trouble shooting
Q. The camera is not recognized every bit a removable deejay or every bit a Webcam.
A. The operating system must be XP or greater. The camera must be continued using a
standard USB cable. Ostend that the cable is not defective by attaching another USB device
using the same cable. Practice not use a USB hub. Try using another USB port. Defective cables
are the most mutual bug when the camera is not correctly recognized past the PC.
Q. The yellow LED flashes once per 2d 15 times and then turns off.
A. There is no micro SD bill of fare inserted, the menu is not properly inserted, the carte is total or the
carte du jour is lacking. The card must be inserted with the gold contacts facing upwards, towards
the buttons. In that location should exist a distinct jump action when inserting the last v mm and at that place
should be no friction whatsoever.
When the carte du jour is pushed i mm within the trunk the menu should latch with a distinctive click.
Never force the card, and never push button the card more than than max. one mm into the camera trunk.
Sometimes the card holder metal frame is non positioned properly in the body and is clearly
visible in the card slot. If this is the instance, insert the card above (on the button side) of the
visible metal frame.
Q1. After I plough the camera on it immediately turns off (the red LED may besides glimmer 3 times –
meet "LED status indicators").
Q2. When I press the shutter push to take a picture or make a video, the camera reacts
usually, but afterward about thirty seconds the camera turns off (the ruby LED may also blink three times
– see "LED status indicators").
Q3. When I printing the shutter button to accept a picture, the red LED is on every bit normal, just I tin
also encounter the yellow LED flashing at the aforementioned time. Later on about xxx seconds the camera turns
off (the cherry LED may besides blink 3 times – see "LED status indicators").
A. This indicates that the SD card is total or information on the SD card is non as expected. Maybe the
card was previously used in some other device. Format the card and try again. If this fails, attempt
another card.
Q. The photographic camera does not react. The green LED may be on or off.
A. The firmware may have entered a continuous loop, or the battery may be discharged.
• Make sure the battery is fully charged.
• Utilise a paper clip or similar object to press the Reset button. This should force the
camera to be turned off.
• Look 10 seconds.
• Turn on the camera.
• Every bit a concluding resort, disconnect the battery and reconnect once again afterwards waiting thirty seconds. Q. With or without an inserted card, the yellow LED flashes 5 times fairly quickly (about once
every i/4 second) and then turns off.
A. This can happen when a firmware file is not updated correctly. The photographic camera will also no
longer react to button presses.
• Remove the menu from the camera and utilize a paper clip or similar instrument to briefly
press the reset push. The camera will most probably wink 5 times.
• Using a carte du jour reader or another photographic camera connected every bit a removable device, copy a
known good firmware file (FWMICDVR.BIN) to the carte du jour.
• Insert the card into the lacking photographic camera. Practise NOT turn it on.
• Briefly press the reset button.
• The yellow LED should flash quickly for a few seconds while the firmware is updated.
• Remove the card and, using an external card reader or the "Backdoor" method, delete
the firmware file (see Firmware Update).
Q. Playback is erratic or stutters or the playback colors are psychedelic or the video flashes,
has corrupted blocks etc.
A. Always kickoff copy the video file from the memory card to your hard drive.
• Your PC or graphics carte du jour may non be powerful enough to playback the video stream.
• You may not take enough memory installed in your PC.
• Use VLC Media Actor. Window Media Player often chokes on underpowered
machines.
• Psychedelic colors may likewise indicate problems with the CMOS lens module. Make
certain the CMOS lens cablevision is correctly seated and not cracked. The lens cable is very
fragile.
Q. When I turn on the camera the yellow LED tuns on but the I can't take a video or photo.
The shutter button doesn't react.
A. .Most likely you have dropped the photographic camera and the ribbon cable which connects the lens
assembly to the circuit board has become dislodged. Yous will have to open the photographic camera,
remove the battery and very carefully reseat the ribbon cable. Instructions on how to remove
the lens assembly can be institute in the elementary teaching manual pdf file which was supplied
with the camera.
Getting Help
This camera is the all-time supported photographic camera of it'southward kind. In example of problems or questions your
first finish should be a visit to:
http://www.rcgroups.com/forums/showthread.php?t=1556994.
This thread is dedicated to questions related to the #16 camera. It should exist noted that the
forum is for aeriform RC discussions only, so please avoid mail annihilation off-topic. The outset 5
posts comprise links to all the important information, including a list of sources where you lot tin
purchase this camera. Only purchase from the sources listed. It is very probable that other sources volition
offer simulated copies. These copies are Non original and volition NOT perform as expected.

Source: https://oscarliang.com/how-to-use-808-16-keychain-camera-manual-and-wiki/

Posted by: casianolous1944.blogspot.com